|
[ Back to Leak Detection ]
GAS PUP®
Portable Combustible Gas Leak Detector & Pressure Gauge
As dependable and efficient as a good hunting dog, the Gas Pup does the job of two monitors in one ultra-compact tool. Employing easy-to-use automatic calibration and a single catalytic bead sensor, this state-of-the air instrument not only sniffs out gas leaks, but also measures pressure.
Features & Benefits
- Built-in 0 to 99 psig Pressure Gauge
- One less tool to bring to the worksite
- Autoranging Natural Gas Detection
- No need for operator to turn a knob and wait for a new zero if over-range occurs
- Autozero Upon Start-Up
- No operator intervention required for sensor zero
- Built-In Auto-Calibration Function
- Allows fast and simple instrument calibration at the bench or in the field
- Small Size and Light Weight
- Both natural gas detection and pressure measurement in one 22 oz package
- Rugged Aluminum Case with Built-In Rubber Boot
- Built to withstand the unexpected bumps and falls which go along with field use
- Bar Graph Display in both the ppm and the upper % gas Natural Gas Ranges
- Bar graph allows visual determination of the point of highest gas concentration when used to find leaks
- “Sticky” Bar Graph Display in High Gas Range
- Useful in bar holing to “hold” the highest reading - indicates where an underground leak is located
- One Sensor for All Three Ranges of Natural Gas Detection
- Fewer spare parts required means lower operating costs
Specifications:
- Ranges:
- Natural Gas Detection:
- 0-2,500 ppm
- 0.2-5.0% vol. gas
- 0-99% vol. gas
- Pressure:
- High 0-99 psig
- Low ±9.9 psig referenced to atmospheric pressure
- Delta ±9.9 psig from any reference pressure point between 0 and 99 psig
- Accuracy:
- Natural Gas:
- Low Range ±0.3% gas
- High Range ±3% gas
- Pressure ±5% of reading
- Warm Up Time: 1 minute approx.
- Response Time:
- Natural Gas <15 seconds
- Pressure <5 seconds
- Environmental Conditions: -4 to +122°F (-20 to +50°C), 10 to 95% Relative Humidity (non-condensing)
- Size: 4.7 x 2.3 x 3.7 in. (11.9 x 5.8 x 9.4 cm)
- Weight: 22 oz (625 g)
- Batteries: 3 - AA alkaline
- Battery Life: Typically 6 to 8 hours of continuous operation, and well over a week of operation when used from 50 to 60 minutes a day
- Agency Approvals: MET lab certified to UL913 and CSA C22.2-157, intrinsically safe for use in Class I, Division 1, Groups A, B, C & D hazardous areas
- Warranty: 1 year, including sensor
Ordering Information
| Part Number | Description |
|---|
| 55-8000 | Gas Pup with Hand-Held Gas Probe and Pressure Hose |
| 55-3001 | 30" Plastic Bar Hole Probe |
| 3474-1210 | 30" Aluminum Bar Hole Probe |
| 3474-1110 | 30" Fiberglass Bar Hole Probe |
| 55-0038 | Pressure Hose Assembly with 1/8" Quick Disconnect Socket |
| 55-0072 | Service Line Pressure Testing Kit: Includes tubing, tee fitting with tire-valve port, quick connect fittings, and 1/8" NPT socket |
| 55-0044 | Soft Carrying Case with Shoulder Strap |
| 55-0039 | Hard ABS Plastic Carrying Case |
| 55-8002 | Calibration Kit (gas not included) |
| 51-1121 | Calibration Gas, 2.5% Methane in Air, 103 L |
| 55-0060 | Calibration Gas, 100% Methane, 58 L |
| 51-1816 | Calibration Gas, 500 ppm Methane in Air, 103L |
| 51-7131 | Calibration Gas, 20.9% O2 in Air, 103L |
| 103-5386 | Quick Connect Socket, 1/4" NPT |
| 103-5396 | Quick Connect Socket, 1/8" NPT |
| 55-0040 | Gas Sensor |
| 55-0045 | Inlet Filter, for instrument (package of 2) |
| 5500-7100 | Foam Filters, for probe (box of 10) |
| 5500-7400 | Charcoal Filters, for probe (box of 10) |
| 55-0063 | Water Trap / Filter Assembly |
| 07-1644 | Replacement Filter for Water Trap/Filter Assembly (package of 3) |
|
(581K) Data Sheet
