DOWNLOADS

Download Index

• AGM300 Software
• BACH-COM Software
• BACH-COM Plus Software
• H25-IR Flash Memory Utility
• H25-IR Firmware Image File
• HGM300 Software
• HGM300 PC Software Manual
• HGM200 & HGM200A Software

AGM300 Software

The following software allows an AGM300 Ammonia Gas Monitoring System to be connected to a DOS or Windows (capable of running DOS programs) based PC via the PC's RS-232 port. With this software, you can monitor and control the operation of your Refrigerant Monitoring System from a personal computer.

Unit	Software Version	Notes:
AGM300	v1.52 (95K)	Unzip the downloaded file onto your hard drive or floppy. Start the program by double clicking the filename PC2AGM.EXE.

BACH-COM Data Download Software

Unit	Software Version	Notes:
Used with instruments: CO2 Monitor 2810, 2815 & 2820 StowSeek N2O Monitor 3010 MGC 100	v2.34 (5.6 MB)	*Note: Unzip downloaded file into a separate directory on your hard drive, and then run "setup.exe" to install.

BACH-COM Plus Data Download Software

Unit	Software Version	Notes:
Used with instruments: CO2 Analyzer 2825, 2830 & 2835 Comfort Check 100 & 200 MGC 200	v1.01 (4.6 MB)	*Note: Unzip downloaded file into a separate directory on your hard drive, and then run "setup.exe" to install.

H25-IR Flash Memory Utility

This utility is used to flash the memory of the H25-IR with the appropriate firmware image file.

Unit	Software Version	Notes:
H25-IR	v2.45 (1560 KB)	Unzip downloaded files into a separate directory on your hard drive. Instructions on how to use this utility is included in the zip file.

H25-IR Firmware Image File

Latest firmware image file for the H25-IR.

Unit	Firmware Version	Notes:
H25-IR	v1.68 (125 KB)	Copy the firmware's image BIN file into the same directory that contains the H25-IR Flash Memory Utility. Instructions on how to flash memory is contained in the H25-IR Flash Memory Utility zip file.

HGM300 & HGM MZ Software

The following software allows an HGM300 Refrigerant Monitoring System to be connected to a DOS or Windows (capable of running DOS programs) based PC via the PC's RS-232 port. With this software, you can monitor and control the operation of your Refrigerant Monitoring System from a personal computer.

HGM300 & HGM MZ PC Software Manual (152K)

Unit	Software Version	Notes:
HGM300	v1.0 (150K)	Use with HGM300 units with v1.0 Unit Firmware, which were built June 2001 or before (as indicated by a serial number that starts with AF01 or lower).
HGM MZ & HGM300	v1.53 (64K)	Use with HGM300 & HGM MZ units with v1.21 Unit Firmware or above, which were built August 2001 or later (as indicated by a serial number that starts with AH01 or above). The Firmware version is also indicated on the label on the ROM module inside the HGM300 or HGM MZ. Unzip the downloaded file onto your hard drive or floppy. Start the program by double clicking the filename PC2HGM.EXX.
HGM300 & HGM MZ	v4.00 (8K)	This configuration file must be installed on the host computer where the Lonworks communications software is installed in order to achieve proper communication between the adapter board and the monitor. This .XIF file is a text file and should be opened with NotePad or an equivalent.

HGM200 & HGM200A Software

Unit	Software Version	Notes:
HGM200	v3.04 (218K)	Unzip downloaded file onto a bootable, MS-DOS Startup disk.
HGM200A	v5.04-R (211K)	Unzip downloaded file onto a bootable, MS-DOS Startup disk.
	v7.0 (219K)	Use on HGM200A units with the HGM300 style I/R bench. Unzip downloaded file onto a bootable, MS-DOS Startup disk.